Re: Need help trying to control Integra AV receiver

I am still having issues with control via Command fusion, I can send
the commands via the integra web interface, but i still cannot control
it via my iphone. All I have done is created a basic layout, and put a
button on there. I then added a system called "Integra" set ip to
192.168.1.17, and both ports to 60128 as it is in the integra
settings. Selected TCP and set to maintain constant connection.
connection join is set to 0 and set startup command to none. I then
create a command and call it off and set the command properties to !
1PWR00\x0D This should work shouldn't it? What am I doing wrong?
Thanks for your help.

On Dec 20, 1:23 pm, Richard Cassin <richard.cas...@gmail.com> wrote:
> Sory for not getting back with any feedback havnt had a chance, didnt  
> even think to see if it had a buit in web server, test a command  
> with ! In front an all good, stupid mistake on my part, thanks guys  
> for your help.
>
> Sent from my iPhone
>
> On 20/12/2009, at 1:04 PM, CG <cgt...@gmail.com> wrote:
>
>
>
> > By the way, with the Integra DTR-7.9 receiver I have at the moment has
> > a basic web server built-in that allows you to send a test IP commands
> > in the text box at the bottom of the screen.
>
> > Just access the server using the IP address of the Receiver (without
> > port # 60128) and you should get in.
>
> > some test commands
>
> > !1PWR00     - standby
> > !1PWR01     - on
> > !1AMT01      - mute on
> > !1AMT00      - mute off
>
> > Also if you use Microsoft Telnet from the windows 'start >> run'
> > option, and use the command 'o 192.168.0.5 60128' if your receivers IP
> > address is 192.168.0.5 and port is 60128, you can see the feedback
> > received from the receiver if you manually change settings via the
> > receivers remote, front panel or via the web server.
>
> > On Dec 20, 9:37 am, CG <cgt...@gmail.com> wrote:
> >> You need to put a '!' before the command
>
> >> ie
>
> >> !1PWR00     - standby
> >> !1PWR01     - on
>
> >> On Dec 19, 1:17 am, Fiasco <dgvoll...@gmail.com> wrote:
>
> >>> I have the Integra (Onkyo) RS232 specs if you need them.
>
> >>> The commands are straight ASC, no hex.
>
> >>> On Dec 17, 6:43 am, Jarrod Bell <jar...@guilink.com> wrote:
>
> >>>> Hi Richard,
>
> >>>> What PC software are you using to control?
>
> >>>> The correct command should be:
> >>>> 1PWR00\x0D
>
> >>>> Also try:
> >>>> 1PWR00\x0A\x0D
>
> >>>> The last one is what telnet would be sending.
>
> >>>> Also make sure you have "maintain constant connection" ticked in  
> >>>> the
> >>>> system properties.
>
> >>>> Jarrod
>
> >>>> On Dec 17, 8:08 pm, wogboynz <richard.cas...@gmail.com> wrote:
>
> >>>>> I am trying to control an Integra 5.9 AV receiver via its TCP  
> >>>>> port. I
> >>>>> have set it to the following settings, 1p 192.168.1.17 and port
> >>>>> 60128.
>
> >>>>> I have these same settings in the commandfusion software, I can  
> >>>>> ping
> >>>>> the receiver from my PC. I think my problem is with the data I am
> >>>>> sending it, I am not too sure whether it should be hex or not. The
> >>>>> message to send it for zone 1 off is "1PWR00" with a Carriage  
> >>>>> Return
> >>>>> on the end. I have tried converting it to hex and sending the
> >>>>> following for the zone 1 off command I have tried
> >>>>> "\x31x50x57x52x30x30x0D" "\x31\x50\x57\x52\x30\x30\x0D"  
> >>>>> ""1PWR00"/x0D"
> >>>>> without the quotes except for the ones inside the last example.  
> >>>>> What
> >>>>> am I doing wrong?
>
> >>>>> I can control the unit via my own pc software by sending "1PWR00"
> >>>>> carriage return.
>
> >>>>> Any help would be much appreciated, I have control documentation  
> >>>>> for
> >>>>> integra codes/protocol etc if anyone wants to take a look at that.
>
> >>>>> Cheers,
> >>>>> Richard- Hide quoted text -
>
> >>>> - Show quoted text -- Hide quoted text -
>
> >>> - Show quoted text -- Hide quoted text -
>
> >> - Show quoted text -
>
> > --
>
> > You received this message because you are subscribed to the Google  
> > Groups "CommandFusion" group.
> > To post to this group, send email to commandfusion@googlegroups.com.
> > To unsubscribe from this group, send email to commandfusion+unsubscribe@googlegroups.com
> > .
> > For more options, visit this group athttp://groups.google.com/group/commandfusion?hl=en
> > .

--

You received this message because you are subscribed to the Google Groups "CommandFusion" group.
To post to this group, send email to commandfusion@googlegroups.com.
To unsubscribe from this group, send email to commandfusion+unsubscribe@googlegroups.com.
For more options, visit this group at http://groups.google.com/group/commandfusion?hl=en.