Re: Need help trying to control Integra AV receiver

@CG - Are you controling your integra 7.9 via commandfusion? Do you
have a basic file with the system added to it that I could take a look
at?

I installed telnet as you said and can view the feedback when I press
buttons on the remote, not too sure why I can't get it to work in
commandfusion.

On Dec 20, 1:23 pm, Richard Cassin <richard.cas...@gmail.com> wrote:
> Sory for not getting back with any feedback havnt had a chance, didnt  
> even think to see if it had a buit in web server, test a command  
> with ! In front an all good, stupid mistake on my part, thanks guys  
> for your help.
>
> Sent from my iPhone
>
> On 20/12/2009, at 1:04 PM, CG <cgt...@gmail.com> wrote:
>
>
>
> > By the way, with the Integra DTR-7.9 receiver I have at the moment has
> > a basic web server built-in that allows you to send a test IP commands
> > in the text box at the bottom of the screen.
>
> > Just access the server using the IP address of the Receiver (without
> > port # 60128) and you should get in.
>
> > some test commands
>
> > !1PWR00     - standby
> > !1PWR01     - on
> > !1AMT01      - mute on
> > !1AMT00      - mute off
>
> > Also if you use Microsoft Telnet from the windows 'start >> run'
> > option, and use the command 'o 192.168.0.5 60128' if your receivers IP
> > address is 192.168.0.5 and port is 60128, you can see the feedback
> > received from the receiver if you manually change settings via the
> > receivers remote, front panel or via the web server.
>
> > On Dec 20, 9:37 am, CG <cgt...@gmail.com> wrote:
> >> You need to put a '!' before the command
>
> >> ie
>
> >> !1PWR00     - standby
> >> !1PWR01     - on
>
> >> On Dec 19, 1:17 am, Fiasco <dgvoll...@gmail.com> wrote:
>
> >>> I have the Integra (Onkyo) RS232 specs if you need them.
>
> >>> The commands are straight ASC, no hex.
>
> >>> On Dec 17, 6:43 am, Jarrod Bell <jar...@guilink.com> wrote:
>
> >>>> Hi Richard,
>
> >>>> What PC software are you using to control?
>
> >>>> The correct command should be:
> >>>> 1PWR00\x0D
>
> >>>> Also try:
> >>>> 1PWR00\x0A\x0D
>
> >>>> The last one is what telnet would be sending.
>
> >>>> Also make sure you have "maintain constant connection" ticked in  
> >>>> the
> >>>> system properties.
>
> >>>> Jarrod
>
> >>>> On Dec 17, 8:08 pm, wogboynz <richard.cas...@gmail.com> wrote:
>
> >>>>> I am trying to control an Integra 5.9 AV receiver via its TCP  
> >>>>> port. I
> >>>>> have set it to the following settings, 1p 192.168.1.17 and port
> >>>>> 60128.
>
> >>>>> I have these same settings in the commandfusion software, I can  
> >>>>> ping
> >>>>> the receiver from my PC. I think my problem is with the data I am
> >>>>> sending it, I am not too sure whether it should be hex or not. The
> >>>>> message to send it for zone 1 off is "1PWR00" with a Carriage  
> >>>>> Return
> >>>>> on the end. I have tried converting it to hex and sending the
> >>>>> following for the zone 1 off command I have tried
> >>>>> "\x31x50x57x52x30x30x0D" "\x31\x50\x57\x52\x30\x30\x0D"  
> >>>>> ""1PWR00"/x0D"
> >>>>> without the quotes except for the ones inside the last example.  
> >>>>> What
> >>>>> am I doing wrong?
>
> >>>>> I can control the unit via my own pc software by sending "1PWR00"
> >>>>> carriage return.
>
> >>>>> Any help would be much appreciated, I have control documentation  
> >>>>> for
> >>>>> integra codes/protocol etc if anyone wants to take a look at that.
>
> >>>>> Cheers,
> >>>>> Richard- Hide quoted text -
>
> >>>> - Show quoted text -- Hide quoted text -
>
> >>> - Show quoted text -- Hide quoted text -
>
> >> - Show quoted text -
>
> > --
>
> > You received this message because you are subscribed to the Google  
> > Groups "CommandFusion" group.
> > To post to this group, send email to commandfusion@googlegroups.com.
> > To unsubscribe from this group, send email to commandfusion+unsubscribe@googlegroups.com
> > .
> > For more options, visit this group athttp://groups.google.com/group/commandfusion?hl=en
> > .

--

You received this message because you are subscribed to the Google Groups "CommandFusion" group.
To post to this group, send email to commandfusion@googlegroups.com.
To unsubscribe from this group, send email to commandfusion+unsubscribe@googlegroups.com.
For more options, visit this group at http://groups.google.com/group/commandfusion?hl=en.