Re: Need help trying to control Integra AV receiver

By the way, with the Integra DTR-7.9 receiver I have at the moment has
a basic web server built-in that allows you to send a test IP commands
in the text box at the bottom of the screen.

Just access the server using the IP address of the Receiver (without
port # 60128) and you should get in.

some test commands

!1PWR00 - standby
!1PWR01 - on
!1AMT01 - mute on
!1AMT00 - mute off

Also if you use Microsoft Telnet from the windows 'start >> run'
option, and use the command 'o 192.168.0.5 60128' if your receivers IP
address is 192.168.0.5 and port is 60128, you can see the feedback
received from the receiver if you manually change settings via the
receivers remote, front panel or via the web server.

On Dec 20, 9:37 am, CG <cgt...@gmail.com> wrote:
> You need to put a '!' before the command
>
> ie
>
> !1PWR00     - standby
> !1PWR01     - on
>
> On Dec 19, 1:17 am, Fiasco <dgvoll...@gmail.com> wrote:
>
>
>
> > I have the Integra (Onkyo) RS232 specs if you need them.
>
> > The commands are straight ASC, no hex.
>
> > On Dec 17, 6:43 am, Jarrod Bell <jar...@guilink.com> wrote:
>
> > > Hi Richard,
>
> > > What PC software are you using to control?
>
> > > The correct command should be:
> > > 1PWR00\x0D
>
> > > Also try:
> > > 1PWR00\x0A\x0D
>
> > > The last one is what telnet would be sending.
>
> > > Also make sure you have "maintain constant connection" ticked in the
> > > system properties.
>
> > > Jarrod
>
> > > On Dec 17, 8:08 pm, wogboynz <richard.cas...@gmail.com> wrote:
>
> > > > I am trying to control an Integra 5.9 AV receiver via its TCP port. I
> > > > have set it to the following settings, 1p 192.168.1.17 and port
> > > > 60128.
>
> > > > I have these same settings in the commandfusion software, I can ping
> > > > the receiver from my PC. I think my problem is with the data I am
> > > > sending it, I am not too sure whether it should be hex or not. The
> > > > message to send it for zone 1 off is "1PWR00" with a Carriage Return
> > > > on the end. I have tried converting it to hex and sending the
> > > > following for the zone 1 off command I have tried
> > > > "\x31x50x57x52x30x30x0D" "\x31\x50\x57\x52\x30\x30\x0D" ""1PWR00"/x0D"
> > > > without the quotes except for the ones inside the last example. What
> > > > am I doing wrong?
>
> > > > I can control the unit via my own pc software by sending "1PWR00"
> > > > carriage return.
>
> > > > Any help would be much appreciated, I have control documentation for
> > > > integra codes/protocol etc if anyone wants to take a look at that.
>
> > > > Cheers,
> > > > Richard- Hide quoted text -
>
> > > - Show quoted text -- Hide quoted text -
>
> > - Show quoted text -- Hide quoted text -
>
> - Show quoted text -

--

You received this message because you are subscribed to the Google Groups "CommandFusion" group.
To post to this group, send email to commandfusion@googlegroups.com.
To unsubscribe from this group, send email to commandfusion+unsubscribe@googlegroups.com.
For more options, visit this group at http://groups.google.com/group/commandfusion?hl=en.